วันศุกร์ที่ 31 สิงหาคม พ.ศ. 2550
Internet Connection by WiFi
Wi-Fi is a wireless technology brand owned by the Wi-Fi Alliance intended to improve the interoperability of wireless local area network products based on the IEEE 802.11 standards.Common applications for Wi-Fi include Internet and VoIP phone access, gaming, and network connectivity for consumer electronics such as televisions, DVD players, and digital cameras.DefinitionAccording to the brand style guide of the Wi-Fi Alliance (the owner of the Wi-Fi brand):"Products which successfully pass the Wi-Fi Alliance testing may use the Wi-Fi CERTIFIED brand. The Alliance tests and certifies the interoperability of wireless LAN products based on the IEEE 802.11 standards. Studies show that 88% of consumers prefer products which have been tested by an independent organization."Wi-Fi technologies have gone through several generations since their inception in 1997. Wi-Fi is supported to different extents under Microsoft Windows, Apple Mac OS and open source Unix and Linux operating systems. Contrary to popular belief, Wi-Fi is not an abbreviation for "Wireless Fidelity" (see "Origin and meaning of the term "Wi-Fi"" below).
Uses
A Wi-Fi enabled device such as a PC, cell phone or PDA can connect to the Internet when within range of a wireless network connected to the Internet. The area covered by one or several interconnected access points is called a hotspot. Hotspots can cover as little as a single room with wireless-opaque walls or as much as many square miles covered by overlapping access points. Wi-Fi can also be used to create a mesh network. Both architectures are used in community networks.[citation needed]Wi-Fi also allows connectivity in peer-to-peer (wireless ad-hoc network) mode, which enables devices to connect directly with each other. This connectivity mode is useful in consumer electronics and gaming applications.When the technology was first commercialized there were many problems because consumers could not be sure that products from different vendors would work together. The Wi-Fi Alliance began as a community to solve this issue so as to address the needs of the end user and allow the technology to mature. The Alliance created the branding Wi-Fi CERTIFIED to show consumers that products are interoperable with other products displaying the same branding.Many consumer devices use Wi-Fi. Amongst others, personal computers can network to each other and connect to the Internet, mobile computers can connect to the Internet from any Wi-Fi hotspot, and digital cameras can transfer images wirelessly.Routers which incorporate a DSL or cable modem and a Wi-Fi access point are often used in homes and other premises, and provide Internet access and internetworking to all devices connected wirelessly or by cable into them. Devices supporting Wi-Fi can also be connected in ad-hoc mode for client-to-client connections without a router.Business and industrial Wi-Fi is widespread as of 2007. In business environments, increasing the number of Wi-Fi access points provides redundancy, support for fast roaming and increased overall network capacity by using more channels or creating smaller cells. Wi-Fi enables wireless voice applications (VoWLAN or WVOIP). Over the years, Wi-Fi implementations have moved toward 'thin' access points, with more of the network intelligence housed in a centralized network appliance, relegating individual Access Points to be simply 'dumb' radios. Outdoor applications may utilize true mesh topologies. As of 2007 Wi-Fi installations can provide a secure computer networking gateway, firewall, DHCP server, intrusion detection system, and other functions.In addition to restricted use in homes and offices, Wi-Fi is publicly available at Wi-Fi hotspots provided either free of charge or to subscribers to various providers. Free hotspots are often provided by businesses such as hotels, restaurants, and airports who offer the service to attract or assist clients. Sometimes free Wi-Fi is provided by enthusiasts, or by organisations or authorities who wish to promote business in their area. Metropolitan-wide WiFi (Mu-Fi) already has more than 300 projects in process.
Advantages of Wi-Fi
Wi-Fi allows LANs to be deployed without cabling for client devices, typically reducing the costs of network deployment and expansion. Spaces where cables cannot be run, such as outdoor areas and historical buildings, can host wireless LANs.As of 2007 wireless network adapters are built into most modern laptops. The price of chipsets for Wi-Fi continues to drop, making it an economical networking option included in ever more devices. Wi-Fi has become widespread in corporate infrastructures, which also helps with the deployment of RFID technology that can piggyback on Wi-Fi [2].Different competitive brands of access points and client network interfaces are inter-operable at a basic level of service. Products designated as "Wi-Fi Certified" by the Wi-Fi Alliance are backwards inter-operable. Wi-Fi is a global set of standards. Unlike mobile telephones, any standard Wi-Fi device will work anywhere in the world.Wi-Fi is widely available in more than 250,000 public hotspots and tens of millions of homes and corporate and university campuses worldwide. WPA is not easily cracked if strong passwords are used and WPA2 encryption has no known weaknesses. New protocols for Quality of Service (WMM) make Wi-Fi more suitable for latency-sensitive applications (such as voice and video), and power saving mechanisms (WMM Power Save) improve battery operation.
Disadvantages of Wi-Fi
Spectrum assignments and operational limitations are not consistent worldwide. Most of Europe allows for an additional 2 channels beyond those permitted in the US (1-13 vs 1-11); Japan has one more on top of that (1-14), and some countries, like Spain, prohibit use of the lower-numbered channels. Europe, as of 2007, is now essentially homogeneous in this respect. Some countries, such as Italy, formerly required a 'general authorization' for any Wi-Fi used outside an operator's own premises, or require something akin to an operator registration.[citation needed] Equivalent isotropically radiated power (EIRP) in the EU is limited to 20 dBm (0.1 W).Power consumption is fairly high compared to some other low-bandwidth standards, such as Zigbee and Bluetooth, making battery life a concern.
The most common wireless encryption standard, Wired Equivalent Privacy or WEP, has been shown to be easily breakable even when correctly configured. Wi-Fi Protected Access (WPA and WPA2), which began shipping in 2003, aims to solve this problem and is now available on most products.
Wi-Fi Access Points typically default to an open (encryption-free) mode. Novice users benefit from a zero-configuration device that works out of the box, but without security enabled, providing open wireless access to their LAN. To turn security on requires the user to configure the device, usually via a software graphical user interface (GUI). Wi-Fi networks that are open (unencrypted) can be monitored and used to read and copy data (including personal information) transmitted over the network, unless another security method is used to secure the data, such as a VPN or a secure web page. (HTTPS/Secure Socket Layer)Many 2.4 GHz 802.11b and 802.11g Access points default to the same channel on initial startup, contributing to congestion on certain channels.
To change the channel of operation for an access point requires the user to configure the device.Wi-Fi networks have limited range. A typical Wi-Fi home router using 802.11b or 802.11g with a stock antenna might have a range of 45 m (150 ft) indoors and 90 m (300 ft) outdoors. Range also varies with frequency band. Wi-Fi in the 2.4 GHz frequency block has slightly better range than Wi-Fi in the 5 GHz frequency block. Outdoor range with improved (directional) antennas can be several kilometres or more with line-of-sight.Wi-Fi pollution, or an excessive number of access points in the area, especially on the same or neighboring channel, can prevent access and interfere with the use of other access points by others, caused by overlapping channels in the 802.11g/b spectrum, as well as with decreased signal-to-noise ratio (SNR) between access points. This can be a problem in high-density areas, such as large apartment complexes or office buildings with many Wi-Fi access points. Additionally, other devices use the 2.4 GHz band: microwave ovens, cordless phones, baby monitors, security cameras, and Bluetooth devices can cause significant additional interference. General guidance to those who suffer these forms of interference or network crowding is to migrate to a WiFi 5GHz product (802.11a) usually a dual band product as the 5GHZ band is relatively unused and there are many more channels available. This also requires users to set up the 5GHz band to be the preffered network in the client and to configure each network band to a different name(SSID).It is also an issue when municipalities[3], or other large entities such as universities, seek to provide large area coverage. Everyone is considered equal for the base standard without 802.11e/WMM when they use the band. This openness is also important to the success and widespread use of 2.4 GHz Wi-Fi, but makes it unsuitable for "must-have" public service functions or where reliability is required.Interoperability issues between brands or proprietary deviations from the standard can disrupt connections or lower throughput speeds on other user's devices that are within range. Additionally, Wi-Fi devices do not, as of 2007, pick channels to avoid interference.[citation needed]Standard DevicesWireless access points connects a group of wireless devices to an adjacent wired LAN. An access point is similar to an ethernet hub, relaying data between connected wireless devices in addition to a (usually) single connected wired device, most often an ethernet hub or switch, allowing wireless devices to communicate with other wired devices.Wireless adapters allow devices to connect to a wireless network. These adapters connect to devices using various external or internal interconnects such as PCI, miniPCI, USB, ExpressCard, Cardbus and PC card. Most newer laptop computers are equipped with internal adapters.
Internal cards are generally more difficult to install.Wireless routers integrate WAP, ethernet switch, and internal Router firmware application that provides IP Routing, NAT, and DNS forwarding through an integrated WAN interface. A wireless router allows wired and wireless ethernet LAN devices to connect to a (usually) single WAN device such as cable modem or DSL modem.
A wireless router allows all three devices (mainly the access point and router) to be configured through one central utility. This utility is most usually an integrated web server which serves web pages to wired and wireless LAN clients and often optionally to WAN clients. This utility may also be an application that is run on a desktop computer such as Apple's AirPort.Wireless Ethernet bridges connect a wired network to a wireless network. This is different from an access point in the sense that an access point connects wireless devices to a wired network at the data-link layer. Two wireless bridges may be used to connect two wired networks over a wireless link, useful in situations where a wired connection may be unavailable, such as between two separate homes.Wireless range extenders or wireless repeaters can extend the range of an existing wireless network. Range extenders can be strategically placed to elongate a signal area or allow for the signal area to reach around barriers such as those created in L-shaped corridors. Wireless devices connected through repeaters will suffer from an increased latency for each hop. Additionally, a wireless device at the end of chain of wireless repeaters will have a throughput that is limited by the weakest link within the repeater chain.Most commercial devices (routers, access points, bridges, repeaters) designed for home or business environments use either RP-SMA or RP-TNC antenna connectors. PCI wireless adapters also mainly use RP-SMA connectors. Most PC card and USB wireless only have internal antennas etched on their printed circuit board while some have MMCX connector or MC-Card external connections in addition to an internal antenna. A few USB cards have a RP-SMA connector. Most Mini PCI wireless cards utilize Hirose U.FL connectors, but cards found in various wireless appliances contain all of the connectors listed. Many high-gain (and homebuilt antennas) utilize the Type N connector more commonly used by other radio communications methods.
Internet Access by ADSL
Asymmetric Digital Subscriber Line (ADSL) is a form of DSL, a data communications technology that enables faster data transmission over copper telephone lines than a conventional voiceband modem can provide. It does this by utilizing frequencies that are not used by a voice telephone call. A splitter or micro filters allow a single telephone connection to be used for both ADSL service and voice calls at the same time. Because phone lines vary in quality and weren't initially provisioned with ADSL in mind, it can generally only be used over short distances, typically less than 5 km
At the telephone exchange the line generally terminates at a DSLAM where another frequency splitter separates the voice band signal for the conventional phone network. Data carried by the ADSL is typically routed over the telephone company's data network and eventually reaches a conventional internet network.
Explanation
The distinguishing characteristic of ADSL over other forms of DSL is that the volume of data flow is greater in one direction than the other, i.e. it is asymmetric. Providers usually market ADSL as a service for consumers to connect to the Internet in a relatively passive mode: able to use the higher speed direction for the "download" from the Internet but not needing to run servers that would require high speed in the other direction.
There are both technical and marketing reasons why ADSL is in many places the most common type offered to home users. On the technical side, there is likely to be more crosstalk from other circuits at the DSLAM end (where the wires from many local loops are close together) than at the customer premises. Thus the upload signal is weakest at the noisiest part of the local loop, while the download signal is strongest at the noisiest part of the local loop. It therefore makes technical sense to have the DSLAM transmit at a higher bit rate than does the modem on the customer end. Since the typical home user in fact does prefer a higher download speed, the telephone companies chose to make a virtue out of necessity, hence ADSL. On the marketing side, limiting upload speeds limits the attractiveness of this service to business customers, often causing them to purchase higher cost Digital Signal 1 services instead. In this fashion, it segments the digital communications market between business and home users.
Internet Connection by broadband internet access
Broadband Internet access, often shortened to just "broadband", is high speed Internet access—typically contrasted with dial-up access over modem.Dial-up modems are generally only capable of a maximum bitrate of 56 kbit/s (kilobits per second) and require the full use of a telephone line—whereas broadband technologies supply at least double this speed and generally without disrupting telephone use.Although various minimum speeds have been used in definitions of broadband, ranging up from 64 kbit/s up to 1.0 Mbit/s, the OECD Broadband Statistics report is typical in counting only download speeds equal to or faster than 256 kbit/s as broadband, and the US FCC use 200 kbit/s in their definition.Speeds are defined in terms of maximum download because several common consumer broadband technologies such as ADSL are "asymmetric" - supporting much slower upload speeds than download."Broadband penetration" is now treated as a key economic indicator
Overview
Broadband is often called high-speed Internet, because it usually has a high rate of data transmission. In general, any connection to the customer of 256 kbit/s (0.256 Mbit/s) or more is considered broadband Internet. The International Telecommunication Union Standardization Sector (ITU-T) recommendation I.113 has defined broadband as a transmission capacity that is faster than primary rate ISDN, at 1.5 to 2 Mbit/s. The FCC definition of broadband is 200 kbit/s (0.2 Mbit/s) in one direction, and advanced broadband is at least 200 kbit/s in both directions. The Organization for Economic Co-operation and Development (OECD) has defined broadband as 256 kbit/s in at least one direction and this bit rate is the most common baseline that is marketed as "broadband" around the world. There is no specific bitrate defined by the industry, however, and "broadband" can mean lower-bitrate transmission methods. Some Internet Service Providers (ISPs) use this to their advantage in marketing lower-bitrate connections as broadband.In practice, the advertised bandwidth is not always reliably available to the customer; ISPs often allow a greater number of subscribers than their backbone connection can handle, under the assumption that most users will not be using their full connection capacity very frequently. This aggregation strategy works more often than not, so users can typically burst to their full bandwidth most of the time; however, peer-to-peer (P2P) file sharing systems, often requiring extended durations of high bandwidth, stress these assumptions, and can cause major problems for ISPs who have excessively overbooked their capacity. For more on this topic, see traffic shaping. As takeup for these introductory products increases, telcos are starting to offer higher bit rate services. For existing connections, this most of the time simply involves reconfiguring the existing equipment at each end of the connection.As the bandwidth delivered to end users increases, the market expects that video on demand services streamed over the Internet will become more popular, though at the present time such services generally require specialized networks. The data rates on most broadband services still do not suffice to provide good quality video, as MPEG-2 video requires about 6 Mbit/s for good results. Adequate video for some purposes becomes possible at lower data rates, with rates of 768 kbit/s and 384 kbit/s used for some video conferencing applications, and rates as low as 100 kbit/s used for videophones using H.264/MPEG-4 AVC. The MPEG-4 format delivers high-quality video at 2 Mbit/s, at the high end of cable modem and ADSL performance.Increased bandwidth has already made an impact on newsgroups: postings to groups such as alt.binaries.* have grown from JPEG files to entire CD and DVD images. According to NTL, the level of traffic on their network increased from a daily inbound news feed of 150 gigabytes of data per day and 1 terabyte of data out each day in 2001 to 500 gigabytes of data inbound and over 4 terabytes out each day in 2002
Technology
The standard broadband technologies in most areas are DSL and cable modems. Newer technologies in use include VDSL and pushing optical fiber connections closer to the subscriber in both telephone and cable plants. Fiber-optic communication, while only recently being used in fiber to the premises and fiber to the curb schemes, has played a crucial role in enabling Broadband Internet access by making transmission of information over larger distances much more cost-effective than copper wire technology. In a few areas not served by cable or ADSL, community organizations have begun to install Wi-Fi networks, and in some cities and towns local governments are installing municipal Wi-Fi networks. As of 2006, high speed mobile Internet access has become available at the consumer level in some countries, using the HSDPA and EV-DO technologies. The newest technology being deployed for mobile and stationary broadband access is WiMAX
Internet Connection by Satellite internet
This employs a satellite in geostationary orbit to relay data from the satellite company to each customer. Satellite Internet is usually among the most expensive ways of gaining broadband Internet access, but in rural areas it may only compete with cellular broadband. However, costs have been coming down in recent years to the point that it is becoming more competitive with other high-speed options.Satellite Internet also has a high latency problem caused by the signal having to travel 35,000 km (22,000 miles) out into space to the satellite and back to Earth again. The signal delay can be as much as 500 milliseconds to 900 milliseconds, which makes this service unsuitable for applications requiring real-time user input such as certain multiplayer Internet games and first-person shooters played over the connection. Despite this, it is still possible for many games to still be played, but the scope is limited to real-time strategy or turn-based games. The functionality of live interactive access to a distant computer can also be subject to the problems caused by high latency. These problems are more than tolerable for just basic email access and web browsing and in most cases are barely noticeable.There is no simple way to get around this problem. The delay is primarily due to the speed of light being only 300,000 km/second (186,000 miles per second). Even if all other signaling delays could be eliminated it still takes the electromagnetic wave 233 milliseconds to travel from ground to the satellite and back to the ground, a total of 70,000 km (44,000 miles) to travel from you to the satellite company.Since the satellite is usually being used for two-way communications, the total distance increases to 140,000 km (88,000 miles), which takes a radio wave 466 ms to travel. Factoring in normal delays from other network sources gives a typical connection latency of 500-700 ms. This is far worse latency than even most dial-up modem users' experience, at typically only 150-200 ms total latency.Most satellite Internet providers also have a FAP (Fair Access Policy). Perhaps one of the largest cons against satellite Internet, these FAPs usually throttle a user's throughput to dial-up speeds after a certain "invisible wall" is hit (usually around 200 MB a day). This FAP usually lasts for 24 hours after the wall is hit, and a user's throughput is restored to whatever tier they paid for. This makes bandwidth-intensive activities nearly impossible to complete in a reasonable amount of time (examples include P2P and newsgroup binary downloading).
Advantages
1. True global broadband Internet access availability
2. Mobile connection to the Internet (with some providers)
Disadvantages1. Very high latency compared to other broadband services, especially 2-way satellite service
2. Unreliable: drop-outs are common during travel, inclement weather, and during sunspot activity
3. The narrow-beam highly directional antenna must be accurately pointed to the satellite orbiting overhead
4. The Fair Access Policy limits heavy usage
5. VPN use is discouraged, problematic, and/or restricted with satellite broadband, although available at a price
6. One-way satellite service requires the use of a modem or other data uplink connection 7. VoIP is not supported.
8. Satellite dishes are huge. Although most of them employ plastic to reduce weight, they are typically between 80 and 120 cm (30 to 48 inches) in diameter.
Intenet Connection by ISDN (Integrated Service Digital Network)
Integrated Service Digital Network (ISDN)
Integrated Service Digital Network (ISDN) is one of the oldest high-speed digital access methods for consumers and businesses to connect to the Internet. It is a telephone data service standard. Its use in the United States peaked in the late 1990s prior to the availability of DSL and cable modem technologies. Broadband service is usually compared to ISDN-BRI because this was the standard high-speed access technology that formed a baseline for the challenges faced by the early broadband providers. These providers sought to compete against ISDN by offering faster and cheaper services to consumers.A basic rate ISDN line (known as ISDN-BRI) is an ISDN line with 2 data "bearer" channels (DS0 - 64 kbit/s each). Using ISDN terminal adapters (erroneously called modems), it is possible to bond together 2 or more separate ISDN-BRI lines to reach speeds of 256 kbit/s or more. The ISDN channel bonding technology has been used for video conference applications and high-speed data transmission.Primary rate ISDN, known as ISDN-PRI, is an ISDN line with 23 DS0 channels and total speed of 1,544 kbit/s (US standard). ISDN E1 (European standard) line is an ISDN lines with 30 DS0 channels and total speed of 2,048 kbit/s. Because ISDN is a telephone-based product, a lot of the terminology and physical aspects of the line are shared by the ISDN-PRI used for voice services. An ISDN line can therefore be "provisioned" for voice or data and many different options, depending on the equipment being used at any particular installation, and depending on the offerings of the telephone company's central office switch. Most ISDN-PRI's are used for telephone voice communication using large PBX systems, rather than for data. One obvious exception is that ISP's usually have ISDN-PRI's for handling ISDN data and modem calls.It is mainly of historical interest that many of the earlier ISDN data lines used 56 kbit/s rather than 64 kbit/s "B" channels of data. This caused ISDN-BRI to be offered at both 128 kbit/s and 112 kbit/s rates, depending on the central office's switching equipment.
Advantages:1. Constant data speed at 64 kbit/s for each DS0 channel.
2. Two way high speed symmetric data transmission, unlike ADSL.
3. One of the data channels can be used for phone conversation without disturbing the data transmission through the other data channel. When a phone call is ended, the bearer channel can immediately dial and re-connect itself to the data call.
4. Call setup is very quick.
5. Low latency
6. ISDN Voice clarity is unmatched by other phone services.
7. Caller ID is almost always available for no additional fee.
8. Maximum distance from the central office is much greater than it is for DSL.
9. When using ISDN-BRI, there is the possibility of using the low-bandwidth 16 kbit/s "D" channel for packet data and for always on capabilities.
Disadvantages:1. ISDN offerings are dwindling in the marketplace due to the widespread use of faster and cheaper alternatives.
2. ISDN routers, terminal adapters ("modems"), and telephones are more expensive than ordinary POTS equipment, like dial-up modems.
3. ISDN provisioning can be complicated due to the great number of options available.
4. ISDN users must dial in to a provider that offers ISDN Internet service, which means that the call could be disconnected.
5. ISDN is billed as a phone line, to which is added the bill for Internet ISDN access.
6. "Always on" data connections are not available in all locations.
7. Some telephone companies charge unusual fees for ISDN, including call setup fees, per minute fees, and higher rates than normal for other services.
Internet Connection by Digital subscriber line (DSL)
DSL
DSL or xDSL, is a family of technologies that provide digital data transmission over the wires of a local telephone network. DSL originally stood for digital subscriber loop, although in recent years, many have adopted digital subscriber line as a more marketing-friendly term for the most popular version of consumer-ready DSL, ADSL.Typically, the download speed of consumer DSL services ranges from 256 kilobits per second (kbit/s) to 24,000 kbit/s, depending on DSL technology, line conditions and service level implemented. Typically, upload speed is lower than download speed for Asymmetric Digital Subscriber Line (ADSL) and equal to download speed for Symmetric Digital Subscriber Line (SDSL).
Voice and dataSome variants of DSL connections, like ADSL and VDSL, typically work by dividing the frequencies used in a single phone line into two primary 'bands'. The ISP data is carried over the high frequency band (25Khz and above) whereas the voice is carried over the lower frequency band (4Khz and below). (See the ADSL article on how the high frequency band is sub-divided). The user typically installs a DSL filter on each phone. This filters out the high frequencies from the phone, so that the phone only sends or receives the lower frequencies (the human voice), creating two independent 'bands'. Thus the DSL modem and the phone can simultaneously use the same phone line without interfering with each other.
History and Science
Digital subscriber line technology was originally implemented as part of the ISDN specification, which is later reused as IDSL. Higher speed DSL connections like HDSL and SDSL are developed to extend the range of DS1 services on copper lines. Consumer oriented ADSL is designed to operate also on a BRI ISDN line, which itself is a form of DSL, as well as on an analog phone line.DSL, like many other forms of communication, stems directly from Claude Shannon's seminal 1948 scientific paper describing a theory of digital communication. Shannon's A Mathematical Theory of Communication laid out the basic elements of any digital communication:• An information source which produces a message • A transmitter which operates on the message to create a signal which can be sent through a channel • A channel, which is the medium over which the signal carrying the information that comprises the message is sent • A receiver, which transforms the signal back into the message intended for delivery • A destination, which can be a person or a machine, for whom or which the message is intended Joe Lechleider at Bellcore (now Telcordia Technologies) developed ADSL in 1988 by placing wideband digital signals above the existing baseband analog voice signal carried between telephone company central offices and customers on conventional twisted pair cabling.[1]US telephone companies promote DSL to compete with cable modems. DSL service was first provided over a dedicated "dry loop", but when the FCC required ILECs to lease their lines to competing providers such as Earthlink, shared-line DSL became common. Also known as DSL over UNE), this allows a single pair to carry data (via a DSLAM) and analog voice (via a circuit switched telephone switch) at the same time. Inline low-pass filter/splitters keep the high frequency DSL signals out of the user's telephones. Although DSL avoids the voice frequency band, the nonlinear elements in the phone would otherwise generate audible intermodulation products and impair the operation of the data modem.Older ADSL standards can deliver 8 Mbit/s to the customer over about 2 km (1.25 miles) of unshielded twisted pair copper wire. The latest standard, ADSL2+, can deliver up to 24 Mbit/s, depending on the distance from the DSLAM. Distances greater than 2 km (1.25 miles) significantly reduce the bandwidth usable on the wires, thus reducing the data rate.
Equipment
The customer end of the connection consists of a DSL modem. This converts data from the digital signals used by computers into a voltage signal of a suitable frequency range which is then applied to the phone line.In some DSL variations (for example, HDSL), the modem is directly connected to the computer via a serial interface, using protocols such as RS-232 or V.35. In other cases (particularly ADSL), it's common for the customer equipment to be integrated with higher level functionality, such as routing, firewalling, or other application-specific hardware and software. In this case, the entire equipment is usually referred to as a DSL router or DSL gateway.Some kinds of DSL technology require installation of appropriate filters to separate, or "split", the DSL signal from the low frequency voice signal. The separation can be done either at the demarcation point, or can be done with filters installed at the telephone outlets inside the customer premises. Either way has its practical and economical limitations. See ADSL for more information about this.At the exchange, a digital subscriber line access multiplexer (DSLAM) terminates the DSL circuits and aggregates them, where they are handed off onto other networking transports. In the case of ADSL, the voice component is also separated at this step, either by a filter integrated in the DSLAM or by a specialized filtering equipment installed before it. The DSLAM terminates all connections and recovers the original digital information.
DSL technologies
The line length limitations from telephone exchange to subscriber are more restrictive for higher data transmission rates. Technologies such as VDSL provide very high speed, short-range links as a method of delivering "triple play" services (typically implemented in fiber to the curb network architectures).
Example DSL technologies (sometimes called xDSL) include:
High Data Rate Digital Subscriber Line (HDSL), also covered in this article
Symmetric Digital Subscriber Line (SDSL), a standardised version of HDSL
Asymmetric Digital Subscriber Line (ADSL), a version of DSL with a slower upload speed
ISDN Digital Subscriber Line (IDSL)
Rate-Adaptive Digital Subscriber Line (RADSL)
Very High Speed Digital Subscriber Line (VDSL)
Very High Speed Digital Subscriber Line 2 (VDSL2), an improved version of VDSL
Symmetric High-speed Digital Subscriber Line (G.SHDSL), a standardised replacement for early proprietary SDSL by the International Telecommunication Union Telecommunication Standardization Sector
Powerline Digital Subscriber Line (PDSL), a high speed powerline communications solution which modulates high speed data onto existing electricity distribution infrastructure
UDSL Etherloop Ethernet Local Loop
Internet connection by dial up
Dial-up access is a form of Internet access via telephone line. The client uses a modem connected to a computer and a telephone line to dial into an Internet service provider's (ISP) node to establish a modem-to-modem link, which is then routed to the Internet.
Availability
Dial-up requires no additional infrastructure on top of the telephone network. As telephone points are available throughout the world, dial-up remains useful to travelers. Dial-up is usually the only choice available for most rural or remote areas where getting a broadband connection is impossible due to low population and demand. Sometimes dial-up access may also be an alternative to people who have limited budgets as it is offered for free by some, though broadband is now increasingly available at lower prices in countries such as the United States, Canada and the United Kingdom due to market competition.Dial-up requires time to establish a telephone connection (several seconds, depending on the location) and perform handshaking before data transfers can take place. In locales with telephone connection charges, each connection incurs an incremental cost. If calls are time-charged, the duration of the connection incurs costs.Dial-up access is a transient connection, because either the user or the ISP terminates the connection. Internet service providers will often set a limit on connection durations to prevent hogging of access, and will disconnect the user — requiring reconnection and the costs and delays associated with it.
Performance
Modern dial-up modems typically have a maximum theoretical speed of 56 kbit/s (using the V.92 protocol), although in most cases only up to 53 kbit/s is possible due to overhead and, in the United States, FCC regulation. These speeds are currently considered the maximum possible; in many cases transfer speeds will be lower, averaging anywhere between 33-43 kbit/s. Factors such as phone line noise and conditions, as well as the quality of the modem itself, play a large part in determining connection speeds.Dial-up connections usually have high latency that can be as high as 400 ms or even more, which can make online gaming or videoconferencing difficult, if not impossible. Some games, such as Star Wars: Galaxies, The Sims Online, Warcraft 3, Halo: Combat Evolved and Guild Wars are capable of running on 56 K dial-up. Gamers with dial-up connections are often disconnected from game servers due to the "lag", or high latency, of the connection. Many computer games released in 2005 (such as Battlefield 2 or Star Wars: Battlefront 2) are not compatible for online play with dial-up modems. These first person shooter style games are the most sensitive to latency, making playing them impractical on dial-up.
Replacement by broadband
Since approximately the year 2000, broadband Internet access (cable and DSL) has been replacing dial-up access in many parts of the world. The reason for this is mostly due to broadband connections featuring speeds which far exceed the capacity of dial-up, many of which provide speeds greater than 1 Mbit/s, as well as reducing prices under dial-up prices offered by companies such as Verizon. An increasing amount of Internet content such as Macromedia Flash, online gaming and streaming media require large amounts of bandwidth.However, many areas still remain without high speed Internet despite the eagerness of potential customers. This can be attributed to population, location, or sometimes ISPs' lack of interest for whatever reason.Dial-up access is still being used in some areas in the U.S. (MSN/AOL), but is increasingly losing ground to broadband.
วันอังคารที่ 28 สิงหาคม พ.ศ. 2550
Device driver
Device driver
From wikipidia
This article needs additional references or sources for verification.
Please help to improve this article by adding reliable references.
Unverifiable material may be challenged and removed.
This article has been tagged since June 2007.
Windows XP loading drivers during a Safe Mode bootup
A device driver, or software driver is a computer program allowing higher-level computer programs to interact with a computer hardware device.
A driver typically communicates with the device through the computer bus or communications subsystem to which the hardware is connected. When a program invokes a routine in the driver, the driver issues commands to the device, and when the device sends data, the driver invokes routines in the program. Drivers are hardware-dependent and operating-system-specific. They usually provide the interrupt handling required for any necessary asynchronous time-dependent hardware interface.
Device drivers simplify programming by acting like a translator between a device and the applications or operating systems that use it. The higher-level code can be written independently of whatever specific hardware device it may control. Every version of a device, such as a printer, requires its own specialized commands. In contrast, most applications access devices (such as sending a file to a printer) by using high-level, generic commands, such as PRINTLN. The driver accepts these generic statements and converts them into the low-level commands required by the device.
Device drivers can be abstracted into logical and physical layers. Logical layers process data for a class of devices such as ethernet ports or disk drives. Physical layers communicate with a specific device instance. For example, a serial port needs to handle standard communication protocols such as XON/XOFF that are common for all serial port hardware. This would be managed by a serial port logical layer. However, the logical layer needs to communicate with a particular serial port chip. 16550 UART hardware differs from PL-011. The physical layer addresses these chip specific variations. Conventionally, OS requests go to the logical layer first. In turn, the logical layer calls upon the physical layer to implement OS requests in terms understandable by the hardware. Inversely, when a hardware device needs to respond to the OS, it uses the physical layer to speak through the logical layer.
Linux device drivers are built into the OS kernel, and thus get built for the appropriate bit-width automatically. Provided that sufficient technical information about the hardware is available, the Linux kernel team will write the drivers free of charge.[1][2][3] This absolves both hardware vendors and end users from having to worry about drivers.
Additionally, the device drivers can either be built as parts of the kernel or can be built separately as loadable modules. The Windows(TM) .sys files and Linux .ko modules are loadable device drivers. The advantage of loadable device drivers is that they can be loaded only when necessary and then unloaded, thus saving kernel memory.
Development
Writing a device driver requires an in-depth understanding of how the hardware and the software of a given platform function. Drivers "...operate in a highly privileged environment and can cause disaster if they get things wrong..." [1] In contrast, most user-level software on modern operating systems can be stopped without greatly affecting the rest of the system. Even drivers executing in user mode can crash a system if the device is erroneously programmed. These factors make it more difficult and dangerous to diagnose problems.
Thus drivers are usually written by software engineers who come from the companies that develop the hardware. This is because they have better information than most outsiders about the design of their hardware. Moreover, it was traditionally considered in the hardware manufacturer's interest to guarantee that their clients can use their hardware in an optimum way. Typically, the logical device driver (LDD) is written by the operating system vendor, while the physical device driver (PDD) is implemented by the device vendor. But in recent years non-vendors have written numerous device drivers, mainly for use with free operating systems. In such cases, it is important that the hardware manufacturer provides information how the device communicates. Although this information can instead be learned by reverse engineering, this is much more difficult with hardware than it is with software.
Microsoft has attempted to reduce system instability due to poorly written device drivers, by creating a new framework for driver development, called Windows Driver Foundation (WDF). This includes User-Mode Driver Framework (UMDF) that encourages development of certain types of drivers - primarily those that implement a message-based protocol for communicating with their devices - as user mode drivers. If such drivers malfunction, they do not cause system instability. The Kernel-Mode Driver Framework (KMDF) model continues to allow development of kernel-mode device drivers, but attempts to provide standard implementations of functions that are well known to cause problems, including cancellation of I/O operations, power management, and plug and play device support.
Apple has an open-source framework for developing drivers on Mac OS X called the I/O Kit.
Because of the diversity of modern hardware and operating systems, many ways exist in which drivers can be used. Drivers are used for interfacing with:
Local buses of various sorts - in particular, for bus mastering on modern systems
Low-bandwidth I/O buses of various sorts (for pointing devices such as mice, keyboards, USB, etc.)
computer storage devices such as hard disk, CD-ROM and floppy disk buses (ATA, SATA, SCSI)
Implementing support for different file systems
Implementing support for image scanners and digital cameras
Common levels of abstraction for device drivers are
For hardware:
Interfacing directly
Using some higher-level interface (e.g. Video BIOS)
Using another lower-level device driver (e.g. file system drivers using disk drivers)
Simulating work with hardware, while doing something entirely different
For software:
Allowing the operating system direct access to hardware resources
Implementing only primitives
Implementing an interface for non-driver software (e.g. TWAIN)
Implementing a language, sometimes quite high-level (e.g. PostScript)
Choosing and installing the correct device drivers for given hardware is often a key component of computer system configuration.
A particular variant of device drivers are virtual device drivers. They are used in virtualization environments, for example when an MS-DOS program is run on a Microsoft Windows computer or when a guest operating system is run on, for example, a Xen host. Instead of enabling the guest operating system to dialog with hardware, virtual device drivers take the opposite role and emulate a piece of hardware, so that the guest operating system and its drivers running inside a virtual machine can have the illusion of accessing real hardware. Attempts by the guest operating system to access the hardware are routed to the virtual device driver in the host operating system as e.g. function calls. The virtual device driver can also send simulated processor-level events like interrupts into the virtual machine.
วันศุกร์ที่ 24 สิงหาคม พ.ศ. 2550
History of computer
History of computing
From Wikipedia, the free encyclopedia
It is difficult to define any one device as the earliest computer. The very definition of a computer has changed and it is therefore impossible to identify the first computer. Many devices once called "computers" would no longer qualify as such by today's standards.
Originally, the term "computer" referred to a person who performed numerical calculations (a human computer), often with the aid of a mechanical calculating device. Examples of early mechanical computing devices included the abacus, the slide rule and arguably the astrolabe and the Antikythera mechanism (which dates from about 150-100 BC). The end of the Middle Ages saw a re-invigoration of European mathematics and engineering, and Wilhelm Schickard's 1623 device was the first of a number of mechanical calculators constructed by European engineers.
However, none of those devices fit the modern definition of a computer because they could not be programmed. In 1801, Joseph Marie Jacquard made an improvement to the textile loom that used a series of punched paper cards as a template to allow his loom to weave intricate patterns automatically. The resulting Jacquard loom was an important step in the development of computers because the use of punched cards to define woven patterns can be viewed as an early, albeit limited, form of programmability.
In 1837, Charles Babbage was the first to conceptualize and design a fully programmable mechanical computer that he called "The Analytical Engine".[2] Due to limited finance, and an inability to resist tinkering with the design, Babbage never actually built his Analytical Engine.[1]
Large-scale automated data processing of punched cards was performed for the US Census in 1890 by tabulating machines designed by Herman Hollerith and manufactured by the Computing Tabulating Recording Corporation, which later became IBM. By the end of the 19th century a number of technologies that would later prove useful in the realization of practical computers had begun to appear: the punched card, Boolean algebra, the vacuum tube (thermionic valve) and the teleprinter.
During the first half of the 20th century, many scientific computing needs were met by increasingly sophisticated analog computers, which used a direct mechanical or electrical model of the problem as a basis for computation. However, these were not programmable and generally lacked the versatility and accuracy of modern digital computers.
| Computer | Shown working | Binary | Electronic | Programmable | Turing complete |
|---|---|---|---|---|---|
| Zuse Z3 | May 1941 | Yes | No | By punched film stock | Yes (1998) |
| Atanasoff–Berry Computer | Summer 1941 | Yes | Yes | No | No |
| Colossus | December 1943 / January 1944 | Yes | Yes | Partially, by rewiring | No |
| Harvard Mark I – IBM ASCC | 1944 | No | No | By punched paper tape | Yes (1998) |
| ENIAC | 1944 | No | Yes | Partially, by rewiring | Yes |
| 1948 | No | Yes | By Function Table ROM | Yes |
* Konrad Zuse's electromechanical "Z machines". The Z3 (1941) was the first working machine featuring binary arithmetic, including floating point arithmetic and a measure of programmability. In 1998 the Z3 was proved to be Turing complete, therefore being the world's first operational computer.
* The non-programmable Atanasoff–Berry Computer (1941) which used vacuum tube based computation, binary numbers, and regenerative capacitor memory.
* The secret British Colossus computer (1944), which had limited programmability but demonstrated that a device using thousands of tubes could be reasonably reliable and electronically reprogrammable. It was used for breaking German wartime codes.
* The Harvard Mark I (1944), a large-scale electromechanical computer with limited programmability.
* The US Army's Ballistics Research Laboratory ENIAC (1946), which used decimal arithmetic and is sometimes called the first general purpose electronic computer (since Konrad Zuse's Z3 of 1941 used electromagnets instead of electronics). Initially, however, ENIAC had an inflexible architecture which essentially required rewiring to change its programming.
Several developers of ENIAC, recognizing its flaws, came up with a far more flexible and elegant design, which came to be known as the stored program architecture or von Neumann architecture. This design was first formally described by John von Neumann in the paper "First Draft of a Report on the EDVAC", published in 1945. A number of projects to develop computers based on the stored program architecture commenced around this time, the first of these being completed in Great Britain. The first to be demonstrated working was the Manchester Small-Scale Experimental Machine (SSEM) or "Baby". However, the EDSAC, completed a year after SSEM, was perhaps the first practical implementation of the stored program design. Shortly thereafter, the machine originally described by von Neumann's paper—EDVAC—was completed but did not see full-time use for an additional two years.
Vacuum tube Nearly all modern computers implement some form of the stored program architecture, making it the single trait by which the word "computer" is now defined. By this standard, many earlier devices would no longer be called computers by today's definition, but are usually referred to as such in their historical context. While the technologies used in computers have changed dramatically since the first electronic, general-purpose computers of the 1940s, most still use the von Neumann architecture. The design made the universal computer a practical reality.
-based computers were in use throughout the 1950s, but were largely replaced in the 1960s by transistor-based devices, which were smaller, faster, cheaper, used less power and were more reliable. These factors allowed computers to be produced on an unprecedented commercial scale. By the 1970s, the adoption of integrated circuit technology and the subsequent creation of microprocessors such as the Intel 4004 caused another leap in size, speed, cost and reliability. By the 1980s, computers had become sufficiently small and cheap to replace simple mechanical controls in domestic appliances such as washing machines. Around the same time, computers became widely accessible for personal use by individuals in the form of home computers and the now ubiquitous personal computer. In conjunction with the widespread growth of the Internet since the 1990s, personal computers are becoming as common as the television and the telephone and almost all modern electronic devices contain a computer of some kind.
What is computer
Computer
From Wikipedia, the free encyclopedia
A computer is a programmable machine that takes in data and processes it into information we can use.Computers take many physical forms. Early electronic computers were the size of a large room, consuming as much power as several hundred modern personal computers (and were nowhere near as advanced).[1] Today, computers can be made small enough to fit into a wrist watch and be powered from a watch battery. Society has come to recognize personal computers and their portable equivalent, the laptop computer, as icons of the information age; they are what most people think of as "a computer". However, the most common form of computer in use today is by far the embedded computer. Embedded computers are small, simple devices that are often used to control other devices—for example, they may be found in machines ranging from fighter aircraft to industrial robots, digital cameras, and even children's toys.
